11 comments


  • Kenny

    Hi there,
    A very nice article. You’ve inspired me to upgrade my MC500, MC 500 mkii and my MC50 mk1.
    I ordered the new oled displays and soldered them in. They seem to be working okay but i have noticed that some of the screens aren’t appearing: ‘Insert disk’ and so on.
    There are an extra 2 pcb holes in the new board, so 16 instead of 14 on the old one.
    I started the wiring from the bottom holes and left 15 & 16 empty.
    Should i have started at the top? I’m reluctant to resolder everything again.
    Many thanks

    January 11, 2021
    • Paul

      Did you ever get it figured out? I want to do that to mine.

      January 27, 2021
    • amsynths

      Hi, most 20×2 OLED’s just have 14 pins but Pins 15 and 16 should not be used as they are the backlight power to an LCD and were used on the original LCD. Let me know what model of OLED you used and I can double check. The connection is Pin 1 to 14. If you have OLED displaying characters then the connection is good.

      January 27, 2021
  • Paul Lanctot

    Cool. The one I’m looking at has 16 pins, and the original mc500 one has 14. In my unit the 2 wires that go to the transformer come off the other side of the original lcd.

    I’m looking at NHD-0220DZ-FSW-FBW.

    So just put pin one to pin one and the rest in order until 14, and leave the 15, 16 empty?

    https://www.newhavendisplay.com/specs/NHD-0220DZ-FSW-FBW.pdf

    Thanks

    January 28, 2021
  • Paul

    https://www.newhavendisplay.com/specs/NHD-0220DZ-FSW-FBW.pdf

    So just don’t hook up pins 15 and 16 on this? Thanks.

    January 28, 2021
  • Kenny

    Many thanks for all your replies, very helpful.
    The screens I used are
    model No: NHD=0220DZW-AB5
    From Mouser Electronics, Inc.

    January 29, 2021
    • Paul Lanctot

      I’m getting ready to try NHD-0220DZ-NSW-BBW and NHD-0220DZ-FSW-FBW will let you know,what happens

      February 09, 2021
    • Paul Lanctot

      Well I just tried mine and I get nothing on the screen at all on power up. I used pins 1-14.
      Reading 5 volts at pin 2 of the display board. The weird part is that pin one of the display connects to pin 14 of the connector on the main board, but looking at the schematic it made sense to me.
      The data sheet for the display says pins 15 and 16 are power for the backlight- pin 15 needs 5v , pin 16 to ground. So maybe I’ll try that , because the 5volts to pin 2 is for data power, according to the data sheet.

      February 11, 2021
  • Paul Lanctot

    I just tried again with NHD-0220DZW-AB5 – connected pin 3- ( contrast) even though it says it’s not used. the display is working but I have the same problem with “ insert disk “ screen not coming up- I have not yet disabled the transformer that fed the old backlight.

    February 16, 2021
  • Riva Lima

    Great job… What the type of rotary encoder?

    July 07, 2021
  • Pierre

    Hi Congratulations on your willingness to share your experiences with Roland Mc 500, I would like to ask you for advice, I recently bought mc500 even if in the past I had mkII, now I don’t have the sys disk and I don’t even have floppy on pc, i would like to bulk data via midi connection, do you think it is possible if possible
    how do you advise me to achieve my goal.
    Thanks again

    August 17, 2021

Leave a reply to Paul Cancel Reply


Copyright AMSynths 2019