Overview Behringer launched their clone of the RSF Kobol Expander I in late 2023 and I received one of the first to arrive in the UK on 23 October. The original design has some unique features including variable wave shape VCO’s and a filter based on the legendary SSM2040 chip. This post describes the technical design of the Behringer version, how it works and performs and the unique signal levels.
It is important to realise that the Kobol works to its own standard of control voltages which are not the same as standard 5V or 10V Eurorack levels and that control voltages are a mix of bipolar and unipolar. The labelling of the panel in terms of knob value is often representative rather than completely accurate.
Eurorack Mounting The Kobol can be removed from its 3U housing and mounted in a Eurorack case. First step is to remove the panel and main PCB from the supplied case, undo the 8x mounting screws and carefully remove the 16-pin IDC cable on the left (it provides MIDI information, audio out and power to the main PCB). The rear of the PCB has a 16-pin socket, a 6×1 pin set of connectors and a 12-pin IDC connector. The power cable attaches to none of these(!). but fits to an IDC 10-pin socket mounted to the main PCB near the LFO.
This correct 10-pin IDC power socket is not immediately obvious nor is its position mentioned in the User Manual.
Extension Socket This is a 12-pin IDC socket which has no mention in the User Manual. The 12-pins connect to various points on the PCB.

Low Frequency Oscillator This is rather nice design which provides an accurate triangle and square wave from 0.01Hz to over 110Hz. The Behringer circuit is an exact replica but with a V13700 OTA chip rather than CA3080. The LFO waveforms have these sizes:
- LFO Square = 0 to +12V
- LFO Triangle = 10V p-t-p (bi-polar waveform)
There is a mistake in the Behringer User Manual, it incorrectly states that the LFO has a S&H option. Unfortunately there is no S&H in the Expander I, have no wait for the II!

Oscillators There are two identical stable and accurate VCO’s that provide seven different waveforms, which are continuously variable under voltage control and a front panel control knob. The UA726 in the original has been replaced with a dual matched transistor and Tempco (which is what I would do….).
Wave generators are like the original but with TL074 Op Amps and V13700 OTAs. Pitch is accurate to 1 cent over 5 octaves. The VCO outputs are lower than typically found in Eurorack modules:
- Triangle: +1.6V
- Shark: +2.5V
- Sawtooth: +3.0V
- Sawsqr: +1.0V
- Square: +2.1V
- Pulse: +2.1V
- Pulse Varying: +2.1V
The oscillators on the Behringer go from will go from 10Hz to 30kHz

Low Pass Filter The Behringer filter is based on a discrete transistor clone of the SSM2040 24dB low pass filter chip, which was used in the original. It uses matched transistor pairs to create the four OTA cells and a transistor array (V3046) is used to drive the stages from a control voltage. The filter will self oscillate down to 20Hz and below, and there is voltage control over resonance. It is a very nice sounding filter with smooth oscillation.
I trimmed the Behringer filter to go down a little lower, making sure the ADS amount control was set to 0 (vertical). The range I set was from 30Hz to 28KHz. The filter capacitors are 0402 size which probably means they are ceramic rather than the nicer sounding PPS type, but the filter does sound very good.
Noise Source The original uses a MN5837 digital noise generating chip (also used in the Prophet 5 Rev 2/3), which is now obsolete. Behringer have used an analog noise circuit which produces bipolar waveforms but with an offset:
- White Noise
- Pink Noise
The MN5837 is known as a psuedo-random noise generator with a distinct and audible repeat pattern due to its 17 stage design. The analog noise source in the Behringer gets round this problem and has no repeatable pattern.
VCA This is a simple voltage controlled amplifier that takes its audio signal input from the VCF, with no external patching available. The level of the VCA is controlled only by the second ADS, with no external CV inputs. There is a final “level” control before the audio out of the Expander. Behringer have used a standard dual OTA (V13700) to create the VCA. A more versatile VCA is available on the Expander II.

Envelope Generators There are two identical ADS envelope generators. The original used SSM2050 chips configured to give Attack, Decay, Sustain and the Release setting the same as the Decay. The first ADS can have its decay set to off, which results in an Attack phase to the Sustain level and then immediate release. The Behringer circuit is based on a 555 timer chip driving a CMOS analog switch. The ADS timings are:
- Attack: 1ms to 15 seconds
- Decay (Release): 1ms to 15 seconds
- Sustain: 0 to +10V
For a more contemporary ADSR (still based on the SMM2050) the Expander II is needed.

Voltage Processor This is a utility module that mixes two CV signals into one, with gain variable from 0 to 2x on input 1 and the sum of 1 and 2. Input one is normalised to +10V. The power rails naturally limit the actual maximum signal level, so x4 on a +10V input is not possible! Measuring the Behringer Expander we get:
- Gain1 at 1x, Gain2 at 1x = +3.8V
- Gain1 at 1x, Gain2 at 2x = +12.8V
- Gain1 at 2x, Gain2 at 1x = +5.1V
- Gain1 at 2x, Gain2 at 1x = +13.2V
Summary A very good technical replica of the original at an amazing low price, it also sounds very nice! The Sonic State review is attached. Take a look at the Expander II and Programmer posts for more RSF information.
If you are looking for an introduction to patching the Kobol Expander and a fab set of 500 patches, try this PDF book on Reverb produced by TSL it is here.


Now am curious how the filter would sound with nicer pps capacitors 🙂
My Benringer one of these is showing as having unipolar negative triangle
waves on both oscillators using a Mordax oscilloscope read out.
The lfo come up as described here and the other vco are primarily unipolar
Is the negative vco triangle normal in the original and this?
Hi,
Sorry I dont have an original to compare the BKobol too. Sorry!
Rob
I really like this reincarnation! Great sound. I just tried to put mine in a Eurorack case and it has 12pin IDC connector rather than 10pin (for which a cable was provided in the box). That makes me puzzled as to what power is expected by Kobol from the Eurorack power bus? Does your unit also have 12 pin connector on the back?
Mine had a 10pin connector on the main panel which I used with a standard Eurorack connector